◀ BACK TO THE COVER — ALL THREE SYSTEMSPRIMER / UNDERCOAT · THE FOUNDATION
GP3201 · SYSTEM 1 — WET-ON-WET PRIMER
GP3201
Germa-Tech SpeedPrimer Plus mixed as a wet-on-wet primer sealer — enhanced levelling and sealing under colour, no sanding: topcoat when the film turns fully matte.
SCAN FOR THE FULL RANGE,
APPLICATION GUIDES & VIDEOS
germatech.com.au
TDS v2.3 · ISSUE 02.09.2026
SUPERSEDES 01.2025
REVIEW DUE 07.2028
3 : 1 : 3 (~100%)
BY VOLUME
GRAVITY Gravity RP Spray, Feed 1.3 mm - 1.4 mm
RP 1.8 - 2.0 bar
1.5 coats maximum (tack coat followed by 1 solid coat)
Tack coat, then ~1 minute between coats*
*ADJUST FOR THE DAY'S TEMPERATURE
01SUITABLE SUBSTRATES
- Sanded existing finishes, putty/body filler, fibreglass or primed surfaces including epoxy, 1k or 2k primer. Direct to sanded galvanised steel or metal (minimum P180/P240) - whilst Germatech 2k Primer will adhere directly to metal, in particular on painted repaired surfaces where sections have been rubbed back to bare, adhesion can only be ensured if surface has been first coated with Germa-Tech Epoxy Primer, in particular large bare surface areas.
- Not stainless steel - stainless steel first requires Epoxy Primer.
- Avoid Direct to Metal - DTM when using speed version of primer (“Spot Repair Primer”) as the accelerated cure process may reduce chemical adhesion times, hence lessen overall adhesion.
02SURFACE PREPARATION
Remove Wax, Silicon and other contaminants with Germa-Tech Prepsol and Germa-Tech Prepsol wipes. Only use Germatech Prepsol Degreaser.
03MIXING — MATCH THE SPEED TO THE WEATHER
GP3201
LESS THAN 23 °C
24 - 32 °C
33 - 38 °C
HARDENER
GP3202 STANDARD OR GP6643 OR GP3102s SLOW FOR LARGER SURFACES
GP6643 OR GP3102s SLOW HARDENER
REDUCER
GP5107/5108 STANDARD REDUCER
GP5108-5XS/5108xs EXTRA SLOW REDUCER
GP5108-5XS/5108xs EXTRA SLOW REDUCER or GP5108-5XXS EXTRA EXTRA SLOW
COLD & DAMP · BELOW 15 °CDo not air dry — bake. Solvent will not leave the film at these temperatures and you get die-back, soft film and blush. Fast hardener, fast reducer.
HOT · ABOVE 30 °CSlow hardener and slow reducer. Flash-off shortens — dry spray, poor flow and mottling in metallics are what a standard system gives you through a hot afternoon.
HUMID · ABOVE 80% RHBlushing risk. Add Retarder Solvent or move to the slow reducer, and do not shorten the flash. Moisture pulled into the film as it chills is what turns it milky.
| TEMPERATURE | PRIMER | HARDENER | REDUCER |
|---|
| LESS THAN 23 °C | GP3201 | GP3202 STANDARD | GP5107/5108 STANDARD REDUCER |
| 24 °C - 32 °C | GP3201 | GP3202 STANDARD OR GP6643 OR GP3102s SLOW FOR LARGER SURFACES | GP5108-5XS/5108xs EXTRA SLOW REDUCER |
| 33 °C - 38 °C | GP3201 | GP6643 OR GP3102s SLOW HARDENER | GP5108-5XS/5108xs EXTRA SLOW REDUCER or GP5108-5XXS EXTRA EXTRA SLOW |
| Ratio by volume | 3 : 1 : 3 (~100%) |
|---|
| Spray viscosity | 13 - 15 seconds |
|---|
| Pot life | ~1.5 hours at below 23 °C · ~1 hour at 24-32 °C |
|---|
| Tinting | Tintable up to 8% with Germa-Tech 2K colour. Tinting the primer toward the topcoat improves colour coverage — and a tinted primer is the correct ground coat, never extra basecoat. |
|---|
| Notes | Can be mixed with 8% Germatech 2K colour to tint primer shades and improve topcoat coverage. |
|---|
BEFORE YOU START — THE SYSTEM IS THE PROCESSGerma-Tech abrasives and ancillary products are graded and tested for compatibility with this product and the process on this sheet — that control is what makes any problem on the job assessable and fixable. Once a non-Germa-Tech product has been used at any step, what actually touched the panel can no longer be verified, and issues that arise cannot be fairly assessed — by us or by anyone. Use the system through the whole process, and if something on this sheet does not fit the job,
talk to us before you spray. Refer to the
GERMA-TECH APPLICATION STANDARD.
04APPLICATION
| Gun — gravity feed | Gravity RP Spray, Feed 1.3 mm - 1.4 mm |
|---|
| Pressure — RP | 1.8 - 2.0 bar |
|---|
| Coats | 1.5 coats maximum (tack coat followed by 1 solid coat) |
|---|
| Flash-off between coats | Tack coat, then ~1 minute between coats |
|---|
| Dry film build | 25-35 µm |
|---|
05DRYING & CURING
| TEMPERATURE | TOPCOAT AFTER |
|---|
| 25 °C | Apply topcoat when Matt - 10-15 min |
06COATING THICKNESS — WHERE THIS SITS IN THE STACK
THIS PRODUCT · GP3201 ▶
25-35 µm
2K primer surfacer
50-80 µm
Body filler
shaped back — not film
SUBSTRATE
bare steel / prepared panel
FULL BUILD
170-270 µm of 300
Read it like the panel: substrate at the bottom, clear on top. Faded rows are the rest of the system at its normal build. See the Coating Thickness Guide.
07RECOAT & REWORK
| Recoat — this product over itself | WET-ON-WET — the flash-off time IS the recoat time. There is no separate recoat window: apply the next coat, or the topcoat, at flash-off — when the film is matt, 10-15 minutes at 25 °C. A sealer left beyond that point is no longer a sealer: treat it as a surfacer and sand before coating. |
|---|
| The next coat over this | Wet-on-wet sealer → topcoat: THE FLASH-OFF TIME IS THE WINDOW — apply the next coat when the film is matt, 10-15 minutes at 25 °C. A sealer left past flash is a surfacer: sand before coating. |
|---|
HOW EACH COAT BONDS — WHY EVERY WINDOW ON THIS SHEET CLOSESThe whole repair is designed as
one system applied within one overall time frame: the primer is dried and sanded, but from colour onward it is a concurrent, same-day process — and every window on this sheet exists to keep you inside it. Within its window the next coat fuses chemically with the film beneath; past it, the film has cured and adhesion must be made mechanically — abrade, degrease, recoat. Heat closes windows sooner: cure runs on temperature, not the clock. Straying from the timed system — jobs interrupted, held over, stretched — is where the problems start. Full explanation in the
GERMA-TECH APPLICATION STANDARD.
If in doubt, abrade. IF YOU MISS THE RECOAT WINDOWOnce the film has cured past its recoat window, do not put another coat straight over it — the new coat sits on the surface and lets go at the interface. Abrade the whole area first (P800 wet or a grey abrasive pad), degrease, tack off, then recoat.
08PHYSICAL PROPERTIES
| Density | approx. 1.29 (relative density, water = 1) — estimated from the Safety Data Sheet; not separately measured |
|---|
| Gloss | N/A — not applicable to a primer |
|---|
| Equipment cleaning | Clean guns and equipment immediately after use with gun wash or a solvent cleaner. Never let mixed 2K product start to cure in the gun — once it kicks, no solvent will save it. |
|---|
09STORAGE, SHELF LIFE & PACKS
| Storage life (unopened) | Up to 36 months unopened — SUBJECT TO correct storage: a cool, dry place below 20 °C, out of direct sun. Heat is the biggest killer of paint in the tin: stock stored or transported in hot vehicles, tin sheds, shipping containers or direct sunlight loses life fast whatever the date on the tin, and that is where most premature failures start. Storage life is an optimal guide, not a promise that survives a hot shed. |
|---|
| Once the seal is broken | Once the seal is broken the clock starts, and how you store it sets the pace. This product: 14 DAYS once the seal is broken, then discard.
All hardeners: 14 days once opened — then discard. Hardener is sealed without air; the moment air enters it starts to deteriorate. A part-used tin resealed tight lasts the 14 days; a loose lid does not. |
|---|
| Storage | Store indoors in a cool, dry place below 20 °C, out of direct sunlight, with the lid sealed tight after every use. Never store or transport in heat — not in a tin shed, a shipping container, a hot van or a sunlit rack. |
|---|
| Pack sizes | 4kgs*4 Cans per box |
|---|
10PRODUCT CODES
| CODE | WHAT IT IS | PACK SIZE |
|---|
| GP3201 | Product | 4KG |
| GP3202 | Hardener · standard | 1LT |
| GP5107 | Reducer · /GP5108 standard | 20LT |
| GP5108SL | Reducer · /GP5108s slow | 5LT |
| GP5108-5XS | Reducer · /GP5108xs extra slow | 5LT |
| GP5108-5XXS | Reducer · extra extra slow | 5LT |
| GP3201 | Colour variant · Grey | 4KG |
| GP3201B | Colour variant · Black | 4KG |
| GP3201W | Colour variant · White | 4KG |
COMPLETE KITSPEED PRIMER GP3201 + SPEED HARDENER GP3202
11WHERE IT SITS IN THE SYSTEM
BARESUBSTRATE
›
EPOXYPRIMER
›
FILLER
›
2K PRIMERSURFACER
›
SEALERWET-ON-WET
›
COLOUR
›
CLEAR
The highlighted step is where this product sits in the repair. Ancillaries support every step.
12STANDARD NOTES — THE SAME ON EVERY SHEET IN THIS SET
- Below 15 °C, air drying at ambient temperature is not recommended — allow a full bake at 60 °C metal temperature. SN1 · ALL BAKEABLE SPRAYED PRODUCTS
- Mix to the stated ratio and use the mix within its pot life. Only use Germa-Tech hardener and reducer — never interchange with another brand. SN2 · ALL MIXED 2K
- At low humidity, a flash-off of 2-3 minutes between coats helps achieve a smooth film. SN3 · ALL SOLVENT-SPRAYED
- Above 30 °C ambient, add Retarder Solvent or move to the slow reducer to avoid blushing — refer to the Retarder Solvent TDS. SN4 · ALL SOLVENT-SPRAYED
- Fisheyes during application: add 0.5-1% Anti Silicon to the remaining paint and respray the affected area. SN6 · ALL SOLVENT-SPRAYED
- Total coating thickness on the panel — every layer together — must not exceed 300 µm. Refer to the Germa-Tech Coating Thickness Guide. SN7 · ALL FILM-BUILDING
- Germa-Tech polyurethane takes up to 12 weeks to fully cure. When reworking or sanding imperfections, take care not to break through the clear into the exposed basecoat — reapplication directly onto sublayers can cause product reactions. Sand imperfections with P1500 working to P3000, then polish. SN8 · ALL POLYURETHANE (ISOCYANATE)
- Do not dry in direct sunlight — panel temperatures in direct sun can exceed 70 °C. Allow 24 hours or a full bake. SN9 · ALL BAKEABLE SPRAYED PRODUCTS
- Germa-Tech products are designed to work as a system — fillers, primers, basecoat, clears, hardeners, reducers, abrasives and ancillaries — each graded and tested for compatibility with the products and processes on this sheet. Performance is only assured within the system, and a fault is only assessable within it: once non-Germa-Tech product has been used in the process, what touched the panel can no longer be verified. SN10 · ALL PRODUCTS
- *Flash-off times are measured at the stated temperature and MUST be adjusted for the day: colder than stated = LONGER flash, warmer = shorter. In winter, shops painting below 23 °C routinely under-flash — solvent is still in the film when the next coat lands. Below 15 °C, extended flash and air dry are not enough: bake the job. SN13 · ALL PRODUCTS WITH A FLASH-OFF
- FINISH FOR COLOUR — THE STANDARD GRADE. The last sanding pass before colour is P500-P600 dry (or P800 wet). METALLIC AND PEARL COLOURS REQUIRE P800, dry or wet — coarser scratches telegraph through the flake and show in the finish. Any coarser grits on this sheet are shaping or stripping stages, not the finish. SN16 · FINISH FOR COLOUR
Standard inclusions are controlled: each note applies to every product in its named set, enforced at build. They cannot drift onto some sheets and off others.
13PRODUCT-SPECIFIC NOTES
- 3. For the colour tuning and non-sanding primer surfacer application process over new panels, the 2K solid colour should be added less than 8%
- 4. Do not add rocket or fast drying additives
- 5. Only use Germatech 2k reducers
- 6. Ensure metal substrates are sanded P180/P240 and existing Sanded surfaces are sanded P400, large metal areas should be Epoxy Primed
- 7. If apply over Epoxy Primer ensure epoxy is sanded P240/P320
AMBIENT TEMPERATURE — WHY EVERY TIME ON THIS SHEET MOVESEvery time on this sheet — flash-off, drying, pot life, the recoat window — is quoted at 20-23 °C, and every one of them moves with temperature, because the two things that set them, solvent evaporation and chemical cure, are both driven by heat. As a working rule cure rate roughly doubles for every 10 °C rise: at 30 °C the times run at about half; at 15 °C they stretch to nearly half speed. Judge by panel temperature, not air temperature — a panel in sun or fresh out of the booth is far hotter than the shed.
HOT WEATHER (above 30 °C): everything shortens. Flash-off comes down, pot life comes down, and the recoat window closes early. Move to the SLOW hardener and slow or extra-slow reducer so the film has time to flow and release solvent — spraying standard speeds in heat is the fast road to dry spray and solvent boil.
COLD WEATHER (below 20 °C): everything stretches. Flash-off gets LONGER — the most common winter mistake is coating over a film that looks flashed but has not released its solvent, which traps it under the next coat and comes back as fry-up, dieback or runs. Move to the FAST hardener, and extend every flash. Below 15 °C standard 2K cure effectively stalls — bake the job, or wait for heat. Cold does not extend the recoat window in proportion either: contamination, moisture and flash rust run on the clock regardless of temperature.
14GOOD TO KNOW — WHAT WE GET CALLED ABOUT
- Do not over coat. Extra or heavy coats trap solvent and wreck the dry times.
- No rocket or fast-drying additives, and Germa-Tech 2K reducers only.
- Grits: metal P180/P240, existing finishes P400, over epoxy P240/P320, hi-fill finished P400-P600.
- On a rapid repair, mix only what you can spray in 20 minutes then clean the gun straight away.
- Keep the speed/spot-repair version off bare metal - the fast cure cuts the adhesion time short.
15TROUBLESHOOTING
| DEFECT | WHAT YOU SEE | WHY IT HAPPENED | FIX |
|---|
Solvent pop | small open craters or burst blisters through the film, usually only obvious after the bake or once the panel has cooled | solvent trapped under a skinned-over film - flash time cut short, coats laid on too heavy, too many coats, or the panel put into the bake before the final flash was done | let the film cure right out, then sand the popped area back to a sound film and refinish; if it has gone through to the undercoat, sand back to the undercoat, re-prime and refinish |
Delamination and peeling | a coat lets go of the one under it - the film peels, flakes or lifts off cleanly in sheets, often starting at an edge or a stone chip | the surface underneath was not keyed or was not clean - missed degrease, wrong or no undercoat, sanding grit too fine or missed altogether, recoat window blown, or basecoat left too long before clear | remove all the loose film back to a sound layer, feather the edge, re-prime and rebuild the system properly |
Shrinkage over filler | the repair looks flat when it leaves the booth and the filler shape shows back through days later, usually as a dull low patch | filler or primer sanded before it had cured through, over-hardened filler, filler applied too thick in one hit, or primer stacked past its coat limit | sand the sunken area back, re-prime with 2K hi-fill, let it cure properly, block flat and refinish |
Edge mapping and ringing | a visible ring or outline of the repair showing through the finished panel, following the featheredge or the primer patch | primer sanded too thin at the featheredge so topcoat solvent reaches the old finish, featheredge grit too coarse, or the primer not fully cured before topcoating | sand the ring back, re-prime over the featheredge with 2K primer, let it cure, and refinish |
Sanding-mark showthrough | the sanding scratch pattern from the stage underneath telegraphs through the finished film, often as fine parallel lines or DA swirls | grit too coarse for the coat going over it, the undercoat not fully cured before it was sanded, or the finish grit skipped so a coarse scratch was never removed | sand the area back flat at the correct finishing grit, re-prime, and refinish |
Die-back and gloss loss | the finish looks right coming out of the booth and then dulls off over the next hours or days | polished or handled before the film had cured, film built too heavy, flash between coats too short, wrong reducer or hardener for conditions, or poor booth air movement | let it cure, then compound and polish; if the gloss will not come up, sand and respray |
AUSTRALIAN CONDITIONSAbove 30 °C ambient, move to the slow hardener and slow reducer and expect flash-off to shorten — dry spray and blushing are what a standard system gives you through a hot afternoon. Below 15 °C, air drying is not recommended: bake. In coastal and high-UV areas do not shortcut the epoxy step on bare metal.
16HEALTH & SAFETY
ISOCYANATE — AIR-SUPPLIED RESPIRATOR REQUIREDThe hardener for this product contains an aromatic polyisocyanate (30-40%) with toluene diisocyanate (<1%) — SDS 7966-14. Spray only in a booth complying with AS/NZS 4114:2020, using
air-supplied respiratory protection — a cartridge respirator is not adequate protection against isocyanate mist. Workers exposed to isocyanates require health monitoring under the model WHS Regulations (Schedule 14) and equivalent state legislation. Refer to the Safe Work Australia
Model Code of Practice: Spray painting and powder coating.
Read the Safety Data Sheet before use. REVISION HISTORY
| VERSION | DATE | CHANGE |
|---|
| v2.3 | 02.09.2026 | Reissued on the current Germa-Tech technical data sheet format. New in this issue: a quick-reference card, the hardener and reducer selection gauge, the coating thickness stack, the recoat-window recovery procedure, and a product-specific troubleshooting table. Bake schedules are now stated as metal temperature. |
17WARRANTY & FURTHER INFORMATION
TALK TO US — WE MEAN ITWe are always happy to talk to customers who contact us directly. If anything on this sheet does not fit the job in front of you — an unusual substrate, a tight timeline, a cold morning, a window you have missed — call before you spray, not after.
support@amproaustralia.com · germatech.com.au This sheet is read together with the GERMA-TECH APPLICATION STANDARD (terms, conditions of application and warranty) and the Coating Thickness Guide — both hosted with the data sheets and at germatech.com.au. Warranty is conditional on correct use of the product as described on this sheet, including the sanding steps and grits in its sanding guide, within the Germa-Tech system. The information in this data sheet is given in good faith and is based on laboratory and field testing. Ampro Australia has no control over the conditions under which this product is used, so the end user must satisfy themselves that the product is suitable for the intended application and conditions. All times are quoted at 20 °C and 50% relative humidity unless stated otherwise. This sheet supersedes all previous issues.
◀ BACK TO THE COVER — ALL THREE SYSTEMSPRIMER / UNDERCOAT · THE FOUNDATION
GP3201 · SYSTEM 2 — PRIMER HI-FILL
GP3201
The same tin mixed as a filling hi-build primer surfacer — strong filling power for the repair you sand back to shape.
SCAN FOR THE FULL RANGE,
APPLICATION GUIDES & VIDEOS
germatech.com.au
TDS v2.3 · ISSUE 02.09.2026
SUPERSEDES 01.2025
REVIEW DUE 07.2028
3 : 1 : 1 (~15-30%)
BY VOLUME
Speed Primer: 15 - 18 seconds
GRAVITY Gravity RP Spray, Feed 1.6-2.0 mm
RP 2.0-2.5 bar
2.5 coats maximum (tack coat followed by 2 solid coats)
50-80 µm
MAXIMUM 80 µm (Hi Fill)
5-10 minutes below 32 °C · 2-3 minutes in high heat*
*ADJUST FOR THE DAY'S TEMPERATURE
01SUITABLE SUBSTRATES
- Sanded existing finishes, putty/body filler, fibreglass or primed surfaces including epoxy, 1k or 2k primer. Direct to sanded galvanised steel or metal (minimum P180/P240) - whilst Germatech 2k Primer will adhere directly to metal, in particular on painted repaired surfaces where sections have been rubbed back to bare, adhesion can only be ensured if surface has been first coated with Germa-Tech Epoxy Primer, in particular large bare surface areas.
- Not stainless steel - stainless steel first requires Epoxy Primer.
- Avoid Direct to Metal - DTM when using speed version of primer (“Spot Repair Primer”) as the accelerated cure process may reduce chemical adhesion times, hence lessen overall adhesion.
02SURFACE PREPARATION
Remove Wax, Silicon and other contaminants with Germa-Tech Prepsol and Germa-Tech Prepsol wipes. Only use Germatech Prepsol Degreaser.
03MIXING — MATCH THE SPEED TO THE WEATHER
GP3201
LESS THAN 23 °C
24 - 32 °C
33 - 38 °C
HARDENER
GP3102 STANDARD or GP3102F FAST (for fast dry or colder climates)
GP6643 OR GP3102s SLOW HARDENER
GP6643 OR GP3102s SLOW HARDENER
REDUCER
GP5107/5108 STANDARD REDUCER
GP5108SL/5108s SLOW REDUCER
GP5108-5XS/5108xs EXTRA SLOW REDUCER
COLD & DAMP · BELOW 15 °CDo not air dry — bake. Solvent will not leave the film at these temperatures and you get die-back, soft film and blush. Fast hardener, fast reducer.
HOT · ABOVE 30 °CSlow hardener and slow reducer. Flash-off shortens — dry spray, poor flow and mottling in metallics are what a standard system gives you through a hot afternoon.
HUMID · ABOVE 80% RHBlushing risk. Add Retarder Solvent or move to the slow reducer, and do not shorten the flash. Moisture pulled into the film as it chills is what turns it milky.
| TEMPERATURE | PRIMER | HARDENER | REDUCER |
|---|
| LESS THAN 23 °C | GP3201 | GP3102 STANDARD or GP3102F FAST (for fast dry or colder climates) | GP5107/5108 STANDARD REDUCER |
| 24 °C - 32 °C | GP3201 | GP6643 OR GP3102s SLOW HARDENER | GP5108SL/5108s SLOW REDUCER |
| 33 °C - 38 °C | GP3201 | GP6643 OR GP3102s SLOW HARDENER | GP5108-5XS/5108xs EXTRA SLOW REDUCER |
| Ratio by volume | 3 : 1 : 1 (~15-30%) |
|---|
| Spray viscosity | Speed Primer: 15 - 18 seconds |
|---|
| Pot life | ~1.5 hours at below 23 °C · ~1 hour at 24-32 °C · ~30-45 minutes at 33-38 °C |
|---|
| Tinting | Tintable up to 8% with Germa-Tech 2K colour. Tinting the primer toward the topcoat improves colour coverage — and a tinted primer is the correct ground coat, never extra basecoat. |
|---|
| Notes | Can be mixed with 8% Germatech 2K colour to tint primer shades and improve topcoat coverage. |
|---|
BEFORE YOU START — THE SYSTEM IS THE PROCESSGerma-Tech abrasives and ancillary products are graded and tested for compatibility with this product and the process on this sheet — that control is what makes any problem on the job assessable and fixable. Once a non-Germa-Tech product has been used at any step, what actually touched the panel can no longer be verified, and issues that arise cannot be fairly assessed — by us or by anyone. Use the system through the whole process, and if something on this sheet does not fit the job,
talk to us before you spray. Refer to the
GERMA-TECH APPLICATION STANDARD.
04APPLICATION
| Gun — gravity feed | Gravity RP Spray, Feed 1.6-2.0 mm |
|---|
| Pressure — RP | 2.0-2.5 bar |
|---|
| Coats | 2.5 coats maximum (tack coat followed by 2 solid coats) |
|---|
| Flash-off between coats | 5-10 minutes below 32 °C · 2-3 minutes in high heat |
|---|
| Dry film build | 50-80 µm |
|---|
| Maximum film build | 80 µm (Hi Fill) |
|---|
05DRYING & CURING
| CONDITION | TEMPERATURE | DRY TO SAND |
|---|
| — | 23 °C | Sandable in 4 hours at 23 °C, less in higher heat |
| bake | 60 °C | 20 minutes |
BAKE TEMPERATURE IS METAL TEMPERATUREBake time starts when the panel reaches temperature, not when the door shuts. A cold panel in a 60 °C booth takes roughly ten minutes to get there — add that to the schedule or the film is under-cured. Baking - Speed Primer Plus at 60 °C: Hi Fill 20 minutes, Spot Repair 5 minutes
06COATING THICKNESS — WHERE THIS SITS IN THE STACK
Sealer / wet-on-wet
25-35 µm
THIS PRODUCT · GP3201 ▶
50-80 µm
Body filler
shaped back — not film
SUBSTRATE
bare steel / prepared panel
FULL BUILD
170-270 µm of 300
Read it like the panel: substrate at the bottom, clear on top. Faded rows are the rest of the system at its normal build. See the Coating Thickness Guide.
MAXIMUM 80 µm (Hi Fill) — THE RED LINE ON THIS PRODUCT'S ROWPast that the film cannot get its solvent out: solvent pop, die-back, a soft film that never fully hardens, and cracking later. Modern polyurethane is a low-build system: less is better. Three thin coats do not fix what two correct coats did — they add microns and take the film past the limit. The red line on the FULL BUILD row is the 300 µm whole-panel ceiling — every layer added together.
07RECOAT & REWORK
| Recoat — this product over itself | RECOAT WINDOW — 2 hours at 20 °C panel temperature from application IF NOT BAKED; after any bake cycle the window is ZERO — the bake closes the film, abrade before recoating. ONCE SANDED the clock restarts: 24 hours from sanding to recoat or apply the next coat (colour). Past 24 hours from sanding, sand again before coating. The 2-hour window moves with temperature — heat shortens it; the 24-hour sanded window does not — a sanded surface is limited by contamination (dust, moisture, flash rust), which runs on the clock regardless of heat. TOPCOAT: THIS SURFACER IS ALWAYS SANDED BEFORE COLOUR — there is no un-sanded route to topcoat. Sand to the finish grade (P500-P600 dry or P800 wet; P800 for metallic and pearl colours), then the 24-hour from-sanding window applies. |
|---|
| The next coat over this | Sanded 2K primer → colour: apply the next coat within 24 HOURS of SANDING the primer. Past 24 hours from sanding, sand again before coating. Contamination-limited — the calendar governs, not the temperature. |
|---|
HOW EACH COAT BONDS — WHY EVERY WINDOW ON THIS SHEET CLOSESThe whole repair is designed as
one system applied within one overall time frame: the primer is dried and sanded, but from colour onward it is a concurrent, same-day process — and every window on this sheet exists to keep you inside it. Within its window the next coat fuses chemically with the film beneath; past it, the film has cured and adhesion must be made mechanically — abrade, degrease, recoat. Heat closes windows sooner: cure runs on temperature, not the clock. Straying from the timed system — jobs interrupted, held over, stretched — is where the problems start. Full explanation in the
GERMA-TECH APPLICATION STANDARD.
If in doubt, abrade. IF YOU MISS THE RECOAT WINDOWOnce the film has cured past its recoat window, do not put another coat straight over it — the new coat sits on the surface and lets go at the interface. Abrade the whole area first (P800 wet or a grey abrasive pad), degrease, tack off, then recoat.
08SANDING GUIDE — STEPS, GRITS & ABRASIVES
| Step | Grit | What you are doing | Germa-Tech abrasives — examples by part number |
|---|
| 1 · Guide coat | — | Dust a contrasting guide coat over the dry primer. It sits in every low spot and scratch — when the guide coat is gone, the panel is flat and proven. | guide coat aerosol/powder |
| 2 · Cut & level | P400 dry | Block or DA the primer level. The guide coat shows exactly where you are. | ORBIT GOLD 150 mm P400 (M6-P400-100) · VIBE long block 115×225 P400 (GSR115400) · BLOCK CERAMIC 70×125 P400 (GSR125400) |
| 3 · Finish for colour | P500–P600 dry (or P800 wet) | Refine the P400 scratch ready for basecoat. Under a direct-gloss 2K colour P400–P500 is enough; under basecoat finish P500–P600. | ORBIT GOLD 150 mm P500 (M6-P500-100) · P600 (M6-P600-100) · SHEER ROLL FOAM 115 P600 (GFR600) for hand work |
| 4 · Feather the edges | P600–P800 | Feather every primer edge into the old finish until you cannot feel it with a bare hand. | ORBIT GOLD 150 mm P800 (M6-P800-100) · SHEER ROLL FOAM 115 P800 (GFR800) |
AFTER SANDING — THE CLOCK STARTSDegrease, tack rag (PB013), and get colour on within 24 hours of sanding — the from-sanding window on this sheet is contamination-limited and does not stretch in cold weather. Leave it longer and the panel needs a re-scuff.
LARGE JOBS — WHEN SANDING TAKES MORE THAN A DAY: on bigger jobs the panels sanded first can be outside the 24-hour window before the last panel is finished. Give the whole job a light scotch rub immediately before colour goes on, and a coat of wet-on-wet primer (GP3201 System 1) is also advised — it seals off any imperfections and puts a fresh, uniform surface under the colour.
THE 100-GRIT RULE — WHY THE SEQUENCE MATTERSEach grit exists to remove the scratches left by the one before it. Never jump more than about 100 grit in one step — a P80 scratch will not come out with P400; it gets buried, then telegraphs through the topcoat weeks later as sanding-mark showthrough. Work the sequence, prove the panel with a guide coat, and step down evenly.
THESE STEPS ARE A WARRANTY CONDITIONFollowing the steps and grits above — with
Germa-Tech abrasives — is a condition of product warranty, not a suggestion. P-grades are only comparable within a controlled range: a recent claim traced to an ungraded brand’s “P320” that cut like a true P240, leaving scratch in the primer that showed through the finished clear. The part numbers above are graded and tested for compatibility with this product and this process — which is what makes a fault assessable: once non-Germa-Tech product has been used, what touched the panel can no longer be verified, and issues arising cannot be fairly assessed. Refer to the
GERMA-TECH APPLICATION STANDARD.
09PHYSICAL PROPERTIES
| Density | approx. 1.29 (relative density, water = 1) — estimated from the Safety Data Sheet; not separately measured |
|---|
| Gloss | N/A — not applicable to a primer |
|---|
| Equipment cleaning | Clean guns and equipment immediately after use with gun wash or a solvent cleaner. Never let mixed 2K product start to cure in the gun — once it kicks, no solvent will save it. |
|---|
10STORAGE, SHELF LIFE & PACKS
| Storage life (unopened) | Up to 36 months unopened — SUBJECT TO correct storage: a cool, dry place below 20 °C, out of direct sun. Heat is the biggest killer of paint in the tin: stock stored or transported in hot vehicles, tin sheds, shipping containers or direct sunlight loses life fast whatever the date on the tin, and that is where most premature failures start. Storage life is an optimal guide, not a promise that survives a hot shed. |
|---|
| Once the seal is broken | Once the seal is broken the clock starts, and how you store it sets the pace. This product: 14 DAYS once the seal is broken, then discard.
All hardeners: 14 days once opened — then discard. Hardener is sealed without air; the moment air enters it starts to deteriorate. A part-used tin resealed tight lasts the 14 days; a loose lid does not. |
|---|
| Storage | Store indoors in a cool, dry place below 20 °C, out of direct sunlight, with the lid sealed tight after every use. Never store or transport in heat — not in a tin shed, a shipping container, a hot van or a sunlit rack. |
|---|
| Pack sizes | 4kgs*4 Cans per box |
|---|
11PRODUCT CODES
| CODE | WHAT IT IS | PACK SIZE |
|---|
| GP3201 | Product | 4KG |
| GP3102 | Hardener · standard | 1LT |
| GP3102F | Hardener · fast | 1LT |
| GP3102S | Hardener · slow | 1LT |
| GP6643 | Hardener · slow | 1LT |
| GP5107 | Reducer · /GP5108 standard | 20LT |
| GP5108SL | Reducer · /GP5108s slow | 5LT |
| GP5108-5XS | Reducer · /GP5108xs extra slow | 5LT |
| GP5108-5XXS | Reducer · extra extra slow | 5LT |
| GP3201 | Colour variant · Grey | 4KG |
| GP3201B | Colour variant · Black | 4KG |
| GP3201W | Colour variant · White | 4KG |
COMPLETE KIT2K PRIMER GP3201 + HARDENER GP3102 (GP3102F fast)
12WHERE IT SITS IN THE SYSTEM
BARESUBSTRATE
›
EPOXYPRIMER
›
FILLER
›
2K PRIMERSURFACER
›
SEALERWET-ON-WET
›
COLOUR
›
CLEAR
The highlighted step is where this product sits in the repair. Ancillaries support every step.
13STANDARD NOTES — THE SAME ON EVERY SHEET IN THIS SET
- Below 15 °C, air drying at ambient temperature is not recommended — allow a full bake at 60 °C metal temperature. SN1 · ALL BAKEABLE SPRAYED PRODUCTS
- Mix to the stated ratio and use the mix within its pot life. Only use Germa-Tech hardener and reducer — never interchange with another brand. SN2 · ALL MIXED 2K
- At low humidity, a flash-off of 2-3 minutes between coats helps achieve a smooth film. SN3 · ALL SOLVENT-SPRAYED
- Above 30 °C ambient, add Retarder Solvent or move to the slow reducer to avoid blushing — refer to the Retarder Solvent TDS. SN4 · ALL SOLVENT-SPRAYED
- Fisheyes during application: add 0.5-1% Anti Silicon to the remaining paint and respray the affected area. SN6 · ALL SOLVENT-SPRAYED
- Total coating thickness on the panel — every layer together — must not exceed 300 µm. Refer to the Germa-Tech Coating Thickness Guide. SN7 · ALL FILM-BUILDING
- Germa-Tech polyurethane takes up to 12 weeks to fully cure. When reworking or sanding imperfections, take care not to break through the clear into the exposed basecoat — reapplication directly onto sublayers can cause product reactions. Sand imperfections with P1500 working to P3000, then polish. SN8 · ALL POLYURETHANE (ISOCYANATE)
- Do not dry in direct sunlight — panel temperatures in direct sun can exceed 70 °C. Allow 24 hours or a full bake. SN9 · ALL BAKEABLE SPRAYED PRODUCTS
- Germa-Tech products are designed to work as a system — fillers, primers, basecoat, clears, hardeners, reducers, abrasives and ancillaries — each graded and tested for compatibility with the products and processes on this sheet. Performance is only assured within the system, and a fault is only assessable within it: once non-Germa-Tech product has been used in the process, what touched the panel can no longer be verified. SN10 · ALL PRODUCTS
- *Flash-off times are measured at the stated temperature and MUST be adjusted for the day: colder than stated = LONGER flash, warmer = shorter. In winter, shops painting below 23 °C routinely under-flash — solvent is still in the film when the next coat lands. Below 15 °C, extended flash and air dry are not enough: bake the job. SN13 · ALL PRODUCTS WITH A FLASH-OFF
- 2.5 COATS means: start with a LIGHT TACK COAT, let it flash, then apply 2 solid coats — and STOP. Less is best. The tack coat sets adhesion and control; the two solid coats do the work. Extra coats add solvent load and film build, not quality. The tack coat and the 24-hour from-sanding rule are GT HOUSE RULES — taught and enforced here, deliberately tighter than published industry practice. The teaching behind this — Application Standard, section 03. SN14 · ALL 2.5-COAT PRODUCTS
- FINISH FOR COLOUR — THE STANDARD GRADE. The last sanding pass before colour is P500-P600 dry (or P800 wet). METALLIC AND PEARL COLOURS REQUIRE P800, dry or wet — coarser scratches telegraph through the flake and show in the finish. Any coarser grits on this sheet are shaping or stripping stages, not the finish. SN16 · FINISH FOR COLOUR
Standard inclusions are controlled: each note applies to every product in its named set, enforced at build. They cannot drift onto some sheets and off others.
14PRODUCT-SPECIFIC NOTES
- 3. For the colour tuning and non-sanding primer surfacer application process over new panels, the 2K solid colour should be added less than 8%
- 4. Do not add rocket or fast drying additives
- 5. Only use Germatech 2k reducers
- 6. Ensure metal substrates are sanded P180/P240 and existing Sanded surfaces are sanded P400, large metal areas should be Epoxy Primed
- 7. If apply over Epoxy Primer ensure epoxy is sanded P240/P320
- 8. Sanding Hi Fill to a finish of P500-P600 dry (or P800 wet)
- 9. Do not over coat - applying more coatings than specified and/or applying too thick will compromise drying times, solvent entrapment and overall coating performance
AMBIENT TEMPERATURE — WHY EVERY TIME ON THIS SHEET MOVESEvery time on this sheet — flash-off, drying, pot life, the recoat window — is quoted at 20-23 °C, and every one of them moves with temperature, because the two things that set them, solvent evaporation and chemical cure, are both driven by heat. As a working rule cure rate roughly doubles for every 10 °C rise: at 30 °C the times run at about half; at 15 °C they stretch to nearly half speed. Judge by panel temperature, not air temperature — a panel in sun or fresh out of the booth is far hotter than the shed.
HOT WEATHER (above 30 °C): everything shortens. Flash-off comes down, pot life comes down, and the recoat window closes early. Move to the SLOW hardener and slow or extra-slow reducer so the film has time to flow and release solvent — spraying standard speeds in heat is the fast road to dry spray and solvent boil.
COLD WEATHER (below 20 °C): everything stretches. Flash-off gets LONGER — the most common winter mistake is coating over a film that looks flashed but has not released its solvent, which traps it under the next coat and comes back as fry-up, dieback or runs. Move to the FAST hardener, and extend every flash. Below 15 °C standard 2K cure effectively stalls — bake the job, or wait for heat. Cold does not extend the recoat window in proportion either: contamination, moisture and flash rust run on the clock regardless of temperature.
15GOOD TO KNOW — WHAT WE GET CALLED ABOUT
- Do not over coat. Extra or heavy coats trap solvent and wreck the dry times.
- No rocket or fast-drying additives, and Germa-Tech 2K reducers only.
- Grits: metal P180/P240, existing finishes P400, over epoxy P240/P320, hi-fill finished P400-P600.
- On a rapid repair, mix only what you can spray in 20 minutes then clean the gun straight away.
- Keep the speed/spot-repair version off bare metal - the fast cure cuts the adhesion time short.
16TROUBLESHOOTING
| DEFECT | WHAT YOU SEE | WHY IT HAPPENED | FIX |
|---|
| Solvent pop | small open craters or burst blisters through the film, usually only obvious after the bake or once the panel has cooled | solvent trapped under a skinned-over film - flash time cut short, coats laid on too heavy, too many coats, or the panel put into the bake before the final flash was done | let the film cure right out, then sand the popped area back to a sound film and refinish; if it has gone through to the undercoat, sand back to the undercoat, re-prime and refinish |
| Delamination and peeling | a coat lets go of the one under it - the film peels, flakes or lifts off cleanly in sheets, often starting at an edge or a stone chip | the surface underneath was not keyed or was not clean - missed degrease, wrong or no undercoat, sanding grit too fine or missed altogether, recoat window blown, or basecoat left too long before clear | remove all the loose film back to a sound layer, feather the edge, re-prime and rebuild the system properly |
| Shrinkage over filler | the repair looks flat when it leaves the booth and the filler shape shows back through days later, usually as a dull low patch | filler or primer sanded before it had cured through, over-hardened filler, filler applied too thick in one hit, or primer stacked past its coat limit | sand the sunken area back, re-prime with 2K hi-fill, let it cure properly, block flat and refinish |
| Edge mapping and ringing | a visible ring or outline of the repair showing through the finished panel, following the featheredge or the primer patch | primer sanded too thin at the featheredge so topcoat solvent reaches the old finish, featheredge grit too coarse, or the primer not fully cured before topcoating | sand the ring back, re-prime over the featheredge with 2K primer, let it cure, and refinish |
| Sanding-mark showthrough | the sanding scratch pattern from the stage underneath telegraphs through the finished film, often as fine parallel lines or DA swirls | grit too coarse for the coat going over it, the undercoat not fully cured before it was sanded, or the finish grit skipped so a coarse scratch was never removed | sand the area back flat at the correct finishing grit, re-prime, and refinish |
| Die-back and gloss loss | the finish looks right coming out of the booth and then dulls off over the next hours or days | polished or handled before the film had cured, film built too heavy, flash between coats too short, wrong reducer or hardener for conditions, or poor booth air movement | let it cure, then compound and polish; if the gloss will not come up, sand and respray |
AUSTRALIAN CONDITIONSAbove 30 °C ambient, move to the slow hardener and slow reducer and expect flash-off to shorten — dry spray and blushing are what a standard system gives you through a hot afternoon. Below 15 °C, air drying is not recommended: bake. In coastal and high-UV areas do not shortcut the epoxy step on bare metal.
17HEALTH & SAFETY
ISOCYANATE — AIR-SUPPLIED RESPIRATOR REQUIREDThe hardener for this product contains an aromatic polyisocyanate (30-40%) with toluene diisocyanate (<1%) — SDS 7966-14. Spray only in a booth complying with AS/NZS 4114:2020, using
air-supplied respiratory protection — a cartridge respirator is not adequate protection against isocyanate mist. Workers exposed to isocyanates require health monitoring under the model WHS Regulations (Schedule 14) and equivalent state legislation. Refer to the Safe Work Australia
Model Code of Practice: Spray painting and powder coating.
Read the Safety Data Sheet before use. REVISION HISTORY
| VERSION | DATE | CHANGE |
|---|
| v2.3 | 02.09.2026 | Reissued on the current Germa-Tech technical data sheet format. New in this issue: a quick-reference card, the hardener and reducer selection gauge, the coating thickness stack, the recoat-window recovery procedure, and a product-specific troubleshooting table. Bake schedules are now stated as metal temperature. |
18WARRANTY & FURTHER INFORMATION
TALK TO US — WE MEAN ITWe are always happy to talk to customers who contact us directly. If anything on this sheet does not fit the job in front of you — an unusual substrate, a tight timeline, a cold morning, a window you have missed — call before you spray, not after.
support@amproaustralia.com · germatech.com.au This sheet is read together with the GERMA-TECH APPLICATION STANDARD (terms, conditions of application and warranty) and the Coating Thickness Guide — both hosted with the data sheets and at germatech.com.au. Warranty is conditional on correct use of the product as described on this sheet, including the sanding steps and grits in its sanding guide, within the Germa-Tech system. The information in this data sheet is given in good faith and is based on laboratory and field testing. Ampro Australia has no control over the conditions under which this product is used, so the end user must satisfy themselves that the product is suitable for the intended application and conditions. All times are quoted at 20 °C and 50% relative humidity unless stated otherwise. This sheet supersedes all previous issues.
◀ BACK TO THE COVER — ALL THREE SYSTEMSPRIMER / UNDERCOAT · THE FOUNDATION
GP3201 · SYSTEM 3 — SPOT REPAIR PRIMER
GP3201
The same tin with the rapid reducer for spot repairs — primed and sandable in around twenty minutes for the job that has to go straight through.
SCAN FOR THE FULL RANGE,
APPLICATION GUIDES & VIDEOS
germatech.com.au
TDS v2.3 · ISSUE 02.09.2026
SUPERSEDES 01.2025
REVIEW DUE 07.2028
3 : 1 : 1 (~30%) rapid thinner
BY VOLUME
less than 20 minutes
below 32 °C · rapid reducer
GRAVITY Gravity RP Spray, Feed 1.6-2.0 mm
RP 2.2-2.5 bar
Speed spot: 1 minute or no flash · standard repair 2-3 minutes · overall 3-5…
see the detail below
*ADJUST FOR THE DAY'S TEMPERATURE
01SUITABLE SUBSTRATES
- Sanded existing finishes, putty/body filler, fibreglass or primed surfaces including epoxy, 1k or 2k primer. Direct to sanded galvanised steel or metal (minimum P180/P240) - whilst Germatech 2k Primer will adhere directly to metal, in particular on painted repaired surfaces where sections have been rubbed back to bare, adhesion can only be ensured if surface has been first coated with Germa-Tech Epoxy Primer, in particular large bare surface areas.
- Not stainless steel - stainless steel first requires Epoxy Primer.
- Avoid Direct to Metal - DTM when using speed version of primer (“Spot Repair Primer”) as the accelerated cure process may reduce chemical adhesion times, hence lessen overall adhesion.
02SURFACE PREPARATION
Remove Wax, Silicon and other contaminants with Germa-Tech Prepsol and Germa-Tech Prepsol wipes. Only use Germatech Prepsol Degreaser.
03MIXING — MATCH THE SPEED TO THE WEATHER
GP3201
LESS THAN 32 °C
ABOVE 32 °C
HARDENER
REDUCER
GP3203 RAPID REPAIR THINNER
GP5107/5108 STANDARD REDUCER
COLD & DAMP · BELOW 15 °CDo not air dry — bake. Solvent will not leave the film at these temperatures and you get die-back, soft film and blush. Fast hardener, fast reducer.
HOT · ABOVE 30 °CSlow hardener and slow reducer. Flash-off shortens — dry spray, poor flow and mottling in metallics are what a standard system gives you through a hot afternoon.
HUMID · ABOVE 80% RHBlushing risk. Add Retarder Solvent or move to the slow reducer, and do not shorten the flash. Moisture pulled into the film as it chills is what turns it milky.
| TEMPERATURE | PRIMER | HARDENER | REDUCER |
|---|
| LESS THAN 32 °C | GP3201 | GP3202 STANDARD | GP3203 RAPID REPAIR THINNER |
| ABOVE 32 °C | GP3201 | GP3202 STANDARD | GP5107/5108 STANDARD REDUCER |
| Ratio by volume | 3 : 1 : 1 (~30%) rapid thinner |
|---|
| Pot life | less than 20 minutes at below 32 °C (rapid reducer) |
|---|
| Tinting | Tintable up to 8% with Germa-Tech 2K colour. Tinting the primer toward the topcoat improves colour coverage — and a tinted primer is the correct ground coat, never extra basecoat. |
|---|
| Notes | Can be mixed with 8% Germatech 2K colour to tint primer shades and improve topcoat coverage. |
|---|
BEFORE YOU START — THE SYSTEM IS THE PROCESSGerma-Tech abrasives and ancillary products are graded and tested for compatibility with this product and the process on this sheet — that control is what makes any problem on the job assessable and fixable. Once a non-Germa-Tech product has been used at any step, what actually touched the panel can no longer be verified, and issues that arise cannot be fairly assessed — by us or by anyone. Use the system through the whole process, and if something on this sheet does not fit the job,
talk to us before you spray. Refer to the
GERMA-TECH APPLICATION STANDARD.
04APPLICATION
| Gun — gravity feed | Gravity RP Spray, Feed 1.6-2.0 mm |
|---|
| Pressure — RP | 2.2-2.5 bar |
|---|
| Coats | 2.5 coats maximum |
|---|
| Flash-off between coats | Speed spot: 1 minute or no flash · standard repair 2-3 minutes · overall 3-5 minutes (adjust up in cooler climates) |
|---|
05DRYING & CURING
| CONDITION | TEMPERATURE | DRY TO SAND |
|---|
| — | — | Dry to sand in 20min |
| bake | 60 °C | 5 minutes |
BAKE TEMPERATURE IS METAL TEMPERATUREBake time starts when the panel reaches temperature, not when the door shuts. A cold panel in a 60 °C booth takes roughly ten minutes to get there — add that to the schedule or the film is under-cured. Baking - Speed Primer Plus at 60 °C: Hi Fill 20 minutes, Spot Repair 5 minutes
06COATING THICKNESS — WHERE THIS SITS IN THE STACK
Sealer / wet-on-wet
25-35 µm
THIS PRODUCT · GP3201 ▶
typ. 50-80 µm — not stated
Body filler
shaped back — not film
SUBSTRATE
bare steel / prepared panel
FULL BUILD
170-270 µm of 300
Read it like the panel: substrate at the bottom, clear on top. Faded rows are the rest of the system at its normal build. See the Coating Thickness Guide.
07RECOAT & REWORK
| Recoat — this product over itself | RECOAT WINDOW — 2 hours at 20 °C panel temperature from application IF NOT BAKED; after any bake cycle the window is ZERO — the bake closes the film, abrade before recoating. ONCE SANDED the clock restarts: 24 hours from sanding to recoat or apply the next coat (colour). Past 24 hours from sanding, sand again before coating. The 2-hour window moves with temperature — heat shortens it; the 24-hour sanded window does not — a sanded surface is limited by contamination (dust, moisture, flash rust), which runs on the clock regardless of heat. TOPCOAT: THIS SURFACER IS ALWAYS SANDED BEFORE COLOUR — there is no un-sanded route to topcoat. Sand to the finish grade (P500-P600 dry or P800 wet; P800 for metallic and pearl colours), then the 24-hour from-sanding window applies. |
|---|
| The next coat over this | Sanded 2K primer → colour: apply the next coat within 24 HOURS of SANDING the primer. Past 24 hours from sanding, sand again before coating. Contamination-limited — the calendar governs, not the temperature. |
|---|
HOW EACH COAT BONDS — WHY EVERY WINDOW ON THIS SHEET CLOSESThe whole repair is designed as
one system applied within one overall time frame: the primer is dried and sanded, but from colour onward it is a concurrent, same-day process — and every window on this sheet exists to keep you inside it. Within its window the next coat fuses chemically with the film beneath; past it, the film has cured and adhesion must be made mechanically — abrade, degrease, recoat. Heat closes windows sooner: cure runs on temperature, not the clock. Straying from the timed system — jobs interrupted, held over, stretched — is where the problems start. Full explanation in the
GERMA-TECH APPLICATION STANDARD.
If in doubt, abrade. IF YOU MISS THE RECOAT WINDOWOnce the film has cured past its recoat window, do not put another coat straight over it — the new coat sits on the surface and lets go at the interface. Abrade the whole area first (P800 wet or a grey abrasive pad), degrease, tack off, then recoat.
08PHYSICAL PROPERTIES
| Density | approx. 1.29 (relative density, water = 1) — estimated from the Safety Data Sheet; not separately measured |
|---|
| Gloss | N/A — not applicable to a primer |
|---|
| Equipment cleaning | Clean guns and equipment immediately after use with gun wash or a solvent cleaner. Never let mixed 2K product start to cure in the gun — once it kicks, no solvent will save it. |
|---|
09STORAGE, SHELF LIFE & PACKS
| Storage life (unopened) | Up to 36 months unopened — SUBJECT TO correct storage: a cool, dry place below 20 °C, out of direct sun. Heat is the biggest killer of paint in the tin: stock stored or transported in hot vehicles, tin sheds, shipping containers or direct sunlight loses life fast whatever the date on the tin, and that is where most premature failures start. Storage life is an optimal guide, not a promise that survives a hot shed. |
|---|
| Once the seal is broken | Once the seal is broken the clock starts, and how you store it sets the pace. This product: 14 DAYS once the seal is broken, then discard.
All hardeners: 14 days once opened — then discard. Hardener is sealed without air; the moment air enters it starts to deteriorate. A part-used tin resealed tight lasts the 14 days; a loose lid does not. |
|---|
| Storage | Store indoors in a cool, dry place below 20 °C, out of direct sunlight, with the lid sealed tight after every use. Never store or transport in heat — not in a tin shed, a shipping container, a hot van or a sunlit rack. |
|---|
| Pack sizes | 4kgs*4 Cans per box |
|---|
10PRODUCT CODES
| CODE | WHAT IT IS | PACK SIZE |
|---|
| GP3201 | Product | 4KG |
| GP3202 | Hardener · standard | 1LT |
| GP5107 | Reducer · /GP5108 standard | 20LT |
| GP3203 | Reducer · Rapid Repair Thinner | 1LT |
| GP3201 | Colour variant · Grey | 4KG |
| GP3201B | Colour variant · Black | 4KG |
| GP3201W | Colour variant · White | 4KG |
COMPLETE KITSPEED PRIMER GP3201 + SPEED HARDENER GP3202 + RAPID REPAIR REDUCER GP3203
11WHERE IT SITS IN THE SYSTEM
BARESUBSTRATE
›
EPOXYPRIMER
›
FILLER
›
2K PRIMERSURFACER
›
SEALERWET-ON-WET
›
COLOUR
›
CLEAR
The highlighted step is where this product sits in the repair. Ancillaries support every step.
12STANDARD NOTES — THE SAME ON EVERY SHEET IN THIS SET
- Below 15 °C, air drying at ambient temperature is not recommended — allow a full bake at 60 °C metal temperature. SN1 · ALL BAKEABLE SPRAYED PRODUCTS
- Mix to the stated ratio and use the mix within its pot life. Only use Germa-Tech hardener and reducer — never interchange with another brand. SN2 · ALL MIXED 2K
- At low humidity, a flash-off of 2-3 minutes between coats helps achieve a smooth film. SN3 · ALL SOLVENT-SPRAYED
- Above 30 °C ambient, add Retarder Solvent or move to the slow reducer to avoid blushing — refer to the Retarder Solvent TDS. SN4 · ALL SOLVENT-SPRAYED
- Fisheyes during application: add 0.5-1% Anti Silicon to the remaining paint and respray the affected area. SN6 · ALL SOLVENT-SPRAYED
- Germa-Tech polyurethane takes up to 12 weeks to fully cure. When reworking or sanding imperfections, take care not to break through the clear into the exposed basecoat — reapplication directly onto sublayers can cause product reactions. Sand imperfections with P1500 working to P3000, then polish. SN8 · ALL POLYURETHANE (ISOCYANATE)
- Do not dry in direct sunlight — panel temperatures in direct sun can exceed 70 °C. Allow 24 hours or a full bake. SN9 · ALL BAKEABLE SPRAYED PRODUCTS
- Germa-Tech products are designed to work as a system — fillers, primers, basecoat, clears, hardeners, reducers, abrasives and ancillaries — each graded and tested for compatibility with the products and processes on this sheet. Performance is only assured within the system, and a fault is only assessable within it: once non-Germa-Tech product has been used in the process, what touched the panel can no longer be verified. SN10 · ALL PRODUCTS
- *Flash-off times are measured at the stated temperature and MUST be adjusted for the day: colder than stated = LONGER flash, warmer = shorter. In winter, shops painting below 23 °C routinely under-flash — solvent is still in the film when the next coat lands. Below 15 °C, extended flash and air dry are not enough: bake the job. SN13 · ALL PRODUCTS WITH A FLASH-OFF
- 2.5 COATS means: start with a LIGHT TACK COAT, let it flash, then apply 2 solid coats — and STOP. Less is best. The tack coat sets adhesion and control; the two solid coats do the work. Extra coats add solvent load and film build, not quality. The tack coat and the 24-hour from-sanding rule are GT HOUSE RULES — taught and enforced here, deliberately tighter than published industry practice. The teaching behind this — Application Standard, section 03. SN14 · ALL 2.5-COAT PRODUCTS
- FINISH FOR COLOUR — THE STANDARD GRADE. The last sanding pass before colour is P500-P600 dry (or P800 wet). METALLIC AND PEARL COLOURS REQUIRE P800, dry or wet — coarser scratches telegraph through the flake and show in the finish. Any coarser grits on this sheet are shaping or stripping stages, not the finish. SN16 · FINISH FOR COLOUR
Standard inclusions are controlled: each note applies to every product in its named set, enforced at build. They cannot drift onto some sheets and off others.
13PRODUCT-SPECIFIC NOTES
- 1. It is recommended to choose conventional thinner for rapid repair when temperature is over 30 °C
- 2. For rapid repair and spraying, mix moderate primer surfacer, spray it within 20 minutes and then clean the spray gun immediately.
- 3. For the colour tuning and non-sanding primer surfacer application process over new panels, the 2K solid colour should be added less than 8%
- 4. Do not add rocket or fast drying additives
- 5. Only use Germatech 2k reducers
- 6. Ensure metal substrates are sanded P180/P240 and existing Sanded surfaces are sanded P400, large metal areas should be Epoxy Primed
- 7. If apply over Epoxy Primer ensure epoxy is sanded P240/P320
WARNINGS CARRIED FORWARD FROM THE PREVIOUS SHEETFast Reducer GP3203 is only used if requiring a speed spot repair (SPEED PRIMER TDS 04.2024)
AMBIENT TEMPERATURE — WHY EVERY TIME ON THIS SHEET MOVESEvery time on this sheet — flash-off, drying, pot life, the recoat window — is quoted at 20-23 °C, and every one of them moves with temperature, because the two things that set them, solvent evaporation and chemical cure, are both driven by heat. As a working rule cure rate roughly doubles for every 10 °C rise: at 30 °C the times run at about half; at 15 °C they stretch to nearly half speed. Judge by panel temperature, not air temperature — a panel in sun or fresh out of the booth is far hotter than the shed.
HOT WEATHER (above 30 °C): everything shortens. Flash-off comes down, pot life comes down, and the recoat window closes early. Move to the SLOW hardener and slow or extra-slow reducer so the film has time to flow and release solvent — spraying standard speeds in heat is the fast road to dry spray and solvent boil.
COLD WEATHER (below 20 °C): everything stretches. Flash-off gets LONGER — the most common winter mistake is coating over a film that looks flashed but has not released its solvent, which traps it under the next coat and comes back as fry-up, dieback or runs. Move to the FAST hardener, and extend every flash. Below 15 °C standard 2K cure effectively stalls — bake the job, or wait for heat. Cold does not extend the recoat window in proportion either: contamination, moisture and flash rust run on the clock regardless of temperature.
14GOOD TO KNOW — WHAT WE GET CALLED ABOUT
- Do not over coat. Extra or heavy coats trap solvent and wreck the dry times.
- No rocket or fast-drying additives, and Germa-Tech 2K reducers only.
- Grits: metal P180/P240, existing finishes P400, over epoxy P240/P320, hi-fill finished P400-P600.
- On a rapid repair, mix only what you can spray in 20 minutes then clean the gun straight away.
- Keep the speed/spot-repair version off bare metal - the fast cure cuts the adhesion time short.
15TROUBLESHOOTING
| DEFECT | WHAT YOU SEE | WHY IT HAPPENED | FIX |
|---|
| Solvent pop | small open craters or burst blisters through the film, usually only obvious after the bake or once the panel has cooled | solvent trapped under a skinned-over film - flash time cut short, coats laid on too heavy, too many coats, or the panel put into the bake before the final flash was done | let the film cure right out, then sand the popped area back to a sound film and refinish; if it has gone through to the undercoat, sand back to the undercoat, re-prime and refinish |
| Delamination and peeling | a coat lets go of the one under it - the film peels, flakes or lifts off cleanly in sheets, often starting at an edge or a stone chip | the surface underneath was not keyed or was not clean - missed degrease, wrong or no undercoat, sanding grit too fine or missed altogether, recoat window blown, or basecoat left too long before clear | remove all the loose film back to a sound layer, feather the edge, re-prime and rebuild the system properly |
| Shrinkage over filler | the repair looks flat when it leaves the booth and the filler shape shows back through days later, usually as a dull low patch | filler or primer sanded before it had cured through, over-hardened filler, filler applied too thick in one hit, or primer stacked past its coat limit | sand the sunken area back, re-prime with 2K hi-fill, let it cure properly, block flat and refinish |
| Edge mapping and ringing | a visible ring or outline of the repair showing through the finished panel, following the featheredge or the primer patch | primer sanded too thin at the featheredge so topcoat solvent reaches the old finish, featheredge grit too coarse, or the primer not fully cured before topcoating | sand the ring back, re-prime over the featheredge with 2K primer, let it cure, and refinish |
| Sanding-mark showthrough | the sanding scratch pattern from the stage underneath telegraphs through the finished film, often as fine parallel lines or DA swirls | grit too coarse for the coat going over it, the undercoat not fully cured before it was sanded, or the finish grit skipped so a coarse scratch was never removed | sand the area back flat at the correct finishing grit, re-prime, and refinish |
| Die-back and gloss loss | the finish looks right coming out of the booth and then dulls off over the next hours or days | polished or handled before the film had cured, film built too heavy, flash between coats too short, wrong reducer or hardener for conditions, or poor booth air movement | let it cure, then compound and polish; if the gloss will not come up, sand and respray |
AUSTRALIAN CONDITIONSAbove 30 °C ambient, move to the slow hardener and slow reducer and expect flash-off to shorten — dry spray and blushing are what a standard system gives you through a hot afternoon. Below 15 °C, air drying is not recommended: bake. In coastal and high-UV areas do not shortcut the epoxy step on bare metal.
16HEALTH & SAFETY
ISOCYANATE — AIR-SUPPLIED RESPIRATOR REQUIREDThe hardener for this product contains an aromatic polyisocyanate (30-40%) with toluene diisocyanate (<1%) — SDS 7966-14. Spray only in a booth complying with AS/NZS 4114:2020, using
air-supplied respiratory protection — a cartridge respirator is not adequate protection against isocyanate mist. Workers exposed to isocyanates require health monitoring under the model WHS Regulations (Schedule 14) and equivalent state legislation. Refer to the Safe Work Australia
Model Code of Practice: Spray painting and powder coating.
Read the Safety Data Sheet before use. REVISION HISTORY
| VERSION | DATE | CHANGE |
|---|
| v2.3 | 02.09.2026 | Reissued on the current Germa-Tech technical data sheet format. New in this issue: a quick-reference card, the hardener and reducer selection gauge, the coating thickness stack, the recoat-window recovery procedure, and a product-specific troubleshooting table. Bake schedules are now stated as metal temperature. |
17WARRANTY & FURTHER INFORMATION
TALK TO US — WE MEAN ITWe are always happy to talk to customers who contact us directly. If anything on this sheet does not fit the job in front of you — an unusual substrate, a tight timeline, a cold morning, a window you have missed — call before you spray, not after.
support@amproaustralia.com · germatech.com.au This sheet is read together with the GERMA-TECH APPLICATION STANDARD (terms, conditions of application and warranty) and the Coating Thickness Guide — both hosted with the data sheets and at germatech.com.au. Warranty is conditional on correct use of the product as described on this sheet, including the sanding steps and grits in its sanding guide, within the Germa-Tech system. The information in this data sheet is given in good faith and is based on laboratory and field testing. Ampro Australia has no control over the conditions under which this product is used, so the end user must satisfy themselves that the product is suitable for the intended application and conditions. All times are quoted at 20 °C and 50% relative humidity unless stated otherwise. This sheet supersedes all previous issues.
